Izdelki za in šobe (56)

Features Full cone spray pattern with a round impact area and uniform distribution. Quick-detachable design helps to greatly reduce maintenance time. Whirler inside a nozzle is removable. Easy mounting/dismounting with a knurled tab. No falling off of tip or packing when removing the nozzle part. [INJJX series (plastic)] Made of high chemical and heat resistant PP (polypropylene). Nozzle tips are color-coded by spray capacity for easy identification. Applications [INJJX series (plastic)] Cleaning Etching Stripping For the applications where precise spray alignment and/or periodic maintenance is required Pipe conn. size:R 1/8" - R 3/8" Spray angle:65–75° Mean droplet diameter:290–520 μm Strainer:Not included Standard pressure:0.2 MPa (ca. 2 bar) Spray capacity:1.00–6.00 ℓ/min Air Consumption:- Free passage diameter:0.8–2.0 mm

Handmatig mondstuk van aluminium. Vloeistofinlaat: 1" BSP (F) - 100 l/min. Bevochtigde materialen:Viton, aluminium Vloeistoffen:Diesel Type uitlaatmondstuk:N.v.t Maximale vrije stroomlevering:100 l/min Vloeistofinlaat:1" BSP (V) Gewicht:0,67 kg (1,47 lb) Meter:N.v.t Bedrijfstemperatuurbereik:-20 - 40 °C (-4 - 104 °F)

The IKO Super Flexible Nozzle is a compact nozzle used on machine tools to supply and spray cutting oil exactly at a specified location. Since the angle of the nozzle can be easily changed, the oil supply can be concentrated on the working area, and cooling and lubrication can be performed effectively. As a result, cutting resistance is reduced and superior finish is obtained, achieving high machining accuracy. The tool life can also be extended, which can result in cost savings. The Super Flexible Nozzle can be used at the spindle end of machining centers and at the tool holder of an NC lathe.

The Flat ionizing air nozzle is used to clean and neutralize electrostatically charged surfaces. The use of compressed air allows awkward places to be neutralized and cleaned as well. Connected to a Simco power unit, the ionizing air nozzles produce an air flow which is rich in positive and negative ions. When this air flow is pointed to an electrostatically charged area, electrons are exchanged until the area is neutralized. This makes that the material is neutralized during the blow-off process and prevents the blown-off particles from being re-attracted. The current of the Flat Nozzle is limited, so that the emitter point is safe to touch. The Flat Nozzle is especially suitable for neutralising at the feeding and delivery sections of machines in the printing industry. Features - Working distance: 50-300 mm - Air consumption: 5 Nm3/h using 1 bar - Max. pressure: 6 bar - Shockless touchable emitters

Features Long flat air nozzle with 100 mm–1,400 mm in spray width. 13 spray width types are available. Max. allowable temperature: 400℃ (750 °F) Applications Blow-off drying: Blow-off drying after washing, Edge wiper for steel surface treatment, Blow-off drying for engine block Blowing off dust/paint dust/debris, Blowing off inferior products (rejection of inferior products) Cooling: Pinpoint cooling for molded plastic Others: Detachment, Cleaning, etc. Spray pattern:Flat Pipe conn. size:R 1/2" - R 1*1/2" Standard pressure:- Spray angle:- Spray capacity:- Supply air type:Compressed air

Features Full cone spray pneumatic nozzle producing fine atomization with a mean droplet diameter of 60 μm or less (*3). Clog-resistant design. Optimal for spraying viscous liquids. Liquid siphon feed type (liquid pressure device is not required). Use with the liquid pressure device is also possible. *1) Measured at compressed air pressure of 0.3 MPa (ca. 3 bar), liquid pressure of 0 MPa (Liquid siphon feed), and siphon height 100 mm. *2) Free passage diameter of liquid inlet. *3) Measured by Laser Doppler Method. Applications Spraying: Mold release agent, deodorant, oil, surface treatment agent, rust preventive, lubricant, honey, glaze, insecticide, aqueous urea, slurry, other viscous liquid Thread standard:- Pipe conn. size:Rc 1/8" Standard pressure:- Spray angle:- Spray capacity:2.0–111 ℓ/hr Supply air type:Compressed air Liquid feeding system:Liquid pressure, Liquid siphon Mean droplet diameter:20–60 μm (*1,*3) Air Consumption:38–290 ℓ/min, Normal Air pressure:0.3 MPa (ca. 3 bar) Free passage diameter:0.5–2.0 mm (*2)

Features High impact solid stream. Convex round inlet protrudes inside the pipe to prevent particles from flowing into the nozzle, reducing clogging. CRP (AL99) series features high-purity alumina orifice providing stable performance with longer life. Applications Cleaning: Wire and felt parts of paper making machines, machinery, parts, vehicles, returnable, containers, bottles Pipe conn. size:R 1/8" - R 1/4" Spray angle:- Mean droplet diameter:- Strainer:Not included Standard pressure:2 MPa (ca. 20 bar) Spray capacity:0.52–8.26 ℓ/min Air Consumption:- Free passage diameter:0.5–2.0 mm

Features 42-mm wide air nozzle. Taking in surrounding air and boosts multiplied air flow. Uniform distribution resulting from the unique flat design. Max. allowable temperature: [Plastic] 120℃ (245°F), [Stainless steel] 400℃ (750 °F) Applications Blow-off drying: Blow-off drying after washing, Edge wiper for steel surface treatment, Blow-off drying for engine block Blowing off dust/paint dust, Rejection of inferior products, Blowing off dust for steel plate Cooling: Pinpoint cooling for molded plastic Spray pattern:Flat Pipe conn. size:R 1/4" Standard pressure:- Spray angle:- Spray capacity:- Supply air type:Compressed air

Features Full cone spray pattern with a round impact area and uniform distribution. Features smallest spray capacity among full cone spray nozzles. Unique design developed from new engineering concept to produce fine atomization by impinging two inflows inside vortex chamber. Ceramic orifice and closer provide excellent wear-resistance. Applications Spraying: Oils, lubricants, glues, etchants Cleaning: Galvanizing, gas Cooling: Machinery, gas Pipe conn. size:R 1/4" Spray angle:70° Mean droplet diameter:130–440 μm Strainer:Included or available Standard pressure:0.2Mpa (ca. 2 bar), 0.5 MPa (ca. 5 bar) Spray capacity:0.09–1.40 ℓ/min Air Consumption:- Free passage diameter:0.2–0.9 mm

Features Full cone spray pattern with a round superimposed impact area. 7 pcs. of KB series hollow cone spray nozzles are screwed into a very compact header. Capable of generating a large volume of fine atomization. The whirl chamber is formed by a ceramic orifice and closer, which provides excellent wear resistance. Applications Gas cooling, Cleaning, Moisture control, Humidification, Dust suppression Pipe conn. size:Rc 3/4" Spray angle:180° Mean droplet diameter:45–210 μm Strainer:Not included Standard pressure:0.7 MPa (ca. 7 bar) Spray capacity:0.23–10.9 ℓ/min Air Consumption:- Free passage diameter:0.15–0.60 mm

Features Extra fine and clear non-turbulent solid stream nozzles with high impact cutting force. Applications Trimming: Paper making Cutting: Timber, food Others: Cleaning of precision machine parts, injection of chemicals, deburring, foaming of beer (jet foamer) Pipe conn. size:R 3/8" Spray angle:- Mean droplet diameter:- Strainer:Included or available Standard pressure:1 MPa (ca. 10 bar) Spray capacity:0.14–1.34 ℓ/min Air Consumption:- Free passage diameter:0.3–1.0 mm

Features Air booster nozzles producing powerful air blow with small air consumption. Taking in surrounding air, EJA series provides ten times more* blown air than the volume supplied. Graduated scale markings on the nozzle allow for accurate adjustment of blown air volume and intake air volume. Made of stainless steel with high durability. *1/4F EJA 300 Applications Blowing off dust/paint dust, Rejection of inferior products, Blowing off drying Blowing extraneous liquids or powders off of items passing by on the conveyor belt Spray pattern:Round Pipe conn. size:Rc 1/8"- Rc 1/4" Standard pressure:- Spray angle:- Spray capacity:- Supply air type:Compressed air

Features Full cone spray pattern with a round impact area and uniform distribution. Spray angle of 120ﾟ provides larger spray coverage than other nozzles. Spray capacity ranges from small to medium. X-shaped whirler provides large free passage diameter for minimal clogging. Applications Cleaning: Gas, incinerator fumes, machinery, eliminators, screen, tanks, parts, crushed stones, earth and sand Cooling: Gas, machineries, tanks, steel plates Spraying: Water treatment, aeration, foam breaking, fire extinguishing, dust suppression, sea water desalination Pipe conn. size:R 1/8" -R 3/8", Rc 3/8" - Rc 4" Spray angle:120° Mean droplet diameter:280–1,200 μm Strainer:Not included Standard pressure:0.2 MPa (ca. 2 bar), 0.35 MPa (ca. 3.5 bar) Spray capacity:0.80–1,200 ℓ/min Air Consumption:- Free passage diameter:0.5–21.7 mm

Features Flat spray nozzles for detergent spraying. Generates large amounts of foam, air suction is driven only by liquid pressure. No compressor is necessary. Cleaning effect is improved due to the long residence time of the foam. *Spray angle of 80° – 100° is for reference only, measured when spraying 100 times diluted commercial dishwasher detergent. Applications Washing outer surface of vehicles Cleaning of conveyors in food industry Pipe conn. size:R 1/4" Spray angle:80-100° Mean droplet diameter:- Strainer:Included or available Standard pressure:0.3 MPa (ca. 3 bar) Spray capacity:1.00–5.00 ℓ/min Air Consumption:- Free passage diameter:-

Features Self-cleaning nozzle header. Inner brushes for nozzle cleaning are built-in. By rotating inner brushes, nozzle orifices are cleaned thoroughly, and foreign objects inside the pipe are flushed out through the drain. Available in the manual brush-cleaning type (the inner brushes are rotated by turning handwheel) and air-driven automatic type (which allows remote control of spray and cleaning modes). *1) Spray capacity per one nozzle (not per header). Applications [Steelmaking] In Continuous Galvanizing Line (CGL), Electrolytic Galvanizing Line (EGL), Continuous Pickling Line (CPL), and Continuous Annealing Line (CAL) Spray capacity:4–20 ℓ/min (*1) Mean droplet diameter:- Power consumption:- Water pressure:0.3 MPa (ca. 3 bar) Air pressure:- Air Consumption:-

Features Flat spray pattern with a mountain-shaped spray distribution having gradually tapered edges. Tapered edges overlap to provide uniformity of spray distribution in multiple-nozzle arrangements. Applications Cleaning: Automotive, containers, films, felts, filters, screens, bottles, crushed stones, earth and sand, metal parts, machines, steel plates and pieces Spraying: Etchants, oils, lubricants, glues, solutions, insecticides, herbicides Cooling: Gas, smokes, heat exchangers, tanks, steels, roofs Water screen: Fire protection, heat protection, dust suppression, deodorization Pipe conn. size:R1/8" - R1" Spray angle:15-115° Mean droplet diameter:150–1,100 μm Strainer:Available for some nozzle codes Standard pressure:0.3 MPa (ca. 3 bar) Spray capacity:0.20–150 ℓ/min Air Consumption:- Free passage diameter:0.2–10.3 mm

Features High impact solid stream of air flown from eight holes. Compact design, lightweight. Quiet operation with noise level reduced by more than 10 dB (A) compared to conventional one-hole air nozzle. Max. allowable temperature: [Plastic] 60℃ (140 °F), [Stainless steel] 400℃ (750 °F). Applications Blow-off drying: Blow-off drying for engine block Blowing off: Rejection of inferior products Cooling: Pinpoint cooling for molded plastic Spray pattern:Flat Pipe conn. size:R 1/8"- R 1/4" Standard pressure:- Spray angle:- Spray capacity:- Supply air type:Compressed air

Features Flat spray pneumatic nozzle producing fine atomization with a mean droplet diameter of 100 μm or less (*3). Features large turn-down ratio under liquid pressures of 0.1–0.3 MPa (ca. 1 bar – 3 bar). Produces two different spray distributions: uniform spray distribution throughout spray pattern area (when spraying at a low air-water ratio), or a mountain-shaped distribution having gradually tapered edges (at a high air-water ratio). Spray angle of 110 °, 80 °, or 45 °. *1) Spray angle measured at compressed air pressure of 0.3 MPa (ca. 3 bar) and liquid pressure of 0.1 MPa (1 bar). *2) Free passage diameter of nozzle orifice. *3) Measured by Laser Doppler Method. Applications Spraying, Cooling, Moisture control, Cleaning, Dust suppression, etc. Thread standard:- Pipe conn. size:- Standard pressure:- Spray angle:45°, 80°, or 110° (*1) Spray capacity:1.0–107 ℓ/hr Supply air type:Compressed air Liquid feeding system:Liquid pressure Mean droplet diameter:20–100 μm Air Consumption:7–245 ℓ/min, Normal Air pressure:0.2–0.4 MPa (ca. 2 bar - 4 bar) Free passage diameter:0.2–1.6 mm (*2)

Features Allows adjustment of spray direction over a range of 50 degrees as desired. [Metal type] Withstands pressure design. Available from 1/8″ to 3/4″ in pipe connection sizes. Use UT-S303 (stainless steel 303) at pressure under 15 MPa (ca. 150 bar), UT-B (brass) under 4 MPa (ca. 40 bar). [Plastic type] Lightweight, high seal performance. Spray direction is adjustable while spraying (up to 0.3 MPa, ca. 3 bar). Use UT-FRPP at pressure under 1 MPa (ca. 10 bar, at room temperature). Cautions for both types: Do not use under conditions where water hammer or sudden change of water pressure occurs. For use with KB and KKBP series nozzles, a different type of UT Ball Joints are required. Inquire with us for details. Applications Accurate nozzle alignment is possible after connected to a pipe. Where large changes in spray direction are required depending on nozzle application such as cleaning and air blowing. Main material:Stainless steel 303, Brass, or Glass-fiber reinforced PP (FRPP)

Features Flat spray pattern with uniform distribution throughout pattern area. Even spray impact across the entire spray area. Applications Cleaning: Automotive, containers, films, felts, filters, screens, bottles, crushed stones, earth and sand, metal parts, machines, steel plates and pieces Spraying: Etchants, oils, lubricants, glues, solutions, insecticides, herbicides Cooling: Gas, smokes, heat exchangers, tanks, steels, roofs Water screen: Fire protection, heat protection, dust suppression, deodorization Pipe conn. size:R1/8" - R1/2" Spray angle:15-115° Mean droplet diameter:140–1,250 μm Strainer:Available for some nozzle codes Standard pressure:0.3 MPa (ca. 3 bar) Spray capacity:0.30–46.9 ℓ/min Air Consumption:- Free passage diameter:0.2–5.8 mm

Features Capable of generating wide-angle flat spray even at low liquid pressure. Clog-resistant Spray direction is 75° to the nozzle axis. Applications Cleaning: Conveyor belts, film, eliminator plates, plate glass, planks Foam breaking: Wastewater treatment, paper manufacturers Cooling: Conveyor belts, roofs, tanks Water screen: Fire protection, heat protection, deodorization Pipe conn. size: R 1/8"- R 1" Spray angle:115-140° Mean droplet diameter:190–1,550 μm Strainer:Available for some nozzle codes Standard pressure:0.15 MPa (ca. 1.5 bar) Spray capacity:0.30–250 ℓ/min Air Consumption:- Free passage diameter:0.6–18.5 mm

Features Easy installation and removal by just attaching a nozzle to this connector. Quick-detachable design helps to greatly reduce maintenance time. Easy mounting/dismounting with a knurled tab. Made of high chemical and heat resistant plastic (compared to PVC). Nozzle connector thread size is Rc 1/8″ or Rc 1/4″. Note: The upper-left photo is INCO with a wide-angle flat spray nozzle YYP series. Applications Cleaning Etching Stripping For the applications where precise spray alignment and/or periodic maintenance is required Quick-detachable nozzle connectors with thread size Rc1/8 or Rc1/4 Main material:PP, PPS

Features Flat spray pneumatic nozzle producing fine atomization with a mean droplet diameter of 100 μm or less (*3). Features large turn-down ratio under liquid pressures of 0.1–0.3 MPa (ca. 1 bar – 3 bar). Produces two different spray distributions: uniform spray distribution throughout spray pattern area (when spraying at a low air-water ratio), or a mountain-shaped distribution having gradually tapered edges (at a high air-water ratio). Spray angle of 110 °, 80 °, or 45 °. *1) Spray angle measured at compressed air pressure of 0.3 MPa (ca. 3 bar) and liquid pressure of 0.1 MPa (ca. 1 bar). *2) Free passage diameter of nozzle orifice. *3) Measured by Laser Doppler Method. Applications Spraying, Cooling, Moisture control, Cleaning, Dust suppression, etc. Thread standard:- Pipe conn. size:M3 depth 2 Standard pressure:- Spray angle:45°, 80°, or 110° (*1) Spray capacity:0.25–38.5 ℓ/hr Supply air type:Compressed air Liquid feeding system:Liquid pressure Mean droplet diameter:20–100 μm Air Consumption:2.6–91 ℓ/min, Normal Air pressure:0.2–0.4 MPa (ca. 2 bar - 4 bar) Free passage diameter:0.2–0.9 mm (*2)

Features Full cone spray pattern with a round impact area and uniform distribution. Unique design to produce fine atomization by liquid impinging inside chamber without a whirler. No-whirler design with large free passage diameter minimizes clogging. Spraying axis 90ﾟ from the axis of the nozzle inlet. For spraying chemicals such as hydrochloric acid, PPS-injection molded AJP are available for excellent chemical and heat resistance. Applications Cleaning: Pre-painting treatment, washing booths, machine parts, gas, incinerator fumes Cooling: Steel plates, copper pieces, gas Spraying: Aeration, foam breaking Others: Applications where re-circulated water is being used or clogging is a concern Pipe conn. size:R 1/8" -R 1*1/2" Spray angle:75-90° Mean droplet diameter:640–1,400 μm Strainer:Not included Standard pressure:0.2 MPa (ca. 2 bar), 0.35 MPa (ca. 3.5 bar) Spray capacity:2.00–250 ℓ/min Air Consumption:- Free passage diameter:1.6–22.3 mm

Features Stable spray pattern at both low and high pressure. Hollow cone spray nozzle with relatively fine atomization. No-whirler design minimizes clogging. Spraying axis 90ﾟ from the axis of the nozzle inlet. Applications Cleaning: Gas, air, machines, pre-painting treatment Cooling: Gas, air handling unit, roofs, machineries, foods, warm water Spraying: Aeration, humidification Pipe conn. size:R 1/4" - R 1/2" Spray angle:75-80° Mean droplet diameter:260–800 μm Strainer:Not included Standard pressure:0.2 MPa (ca. 2 bar) Spray capacity:1.00–23.0 ℓ/min Air Consumption:- Free passage diameter:2.0–8.0 mm

Features Flat spray nozzles specially designed for descaling. Produces razor-like thin, sharp stream with even spray distribution and high spray impact. TDSS series, with much higher spray impact, increases erosion depth by 20% compared to the conventional model. Water-saving. Applications Descaling: rolling process in steelmaking Pipe conn. size:Welding Spray angle:20-65° Mean droplet diameter:- Strainer:Included or available Standard pressure:15 MPa (ca. 15 bar) Spray capacity:15.0–138 ℓ/min Air Consumption:- Free passage diameter:0.7–1.5 mm

Features Flat spray pattern with a mountain-shaped spray distribution having gradually tapered edges. Easy installation just by drilling a hole (φ14.3 mm) on a pipe and inserting a nozzle. Easy assemble and maintenance by quick detachable nozzles. Adaptors, color-coded by size, are available in 1″, 1 “, 1 “, 2”, 25A, and 30A. Spray tips are also color-coded by spray capacity for easy identification. Adjust spray direction within 50 degrees as desired. Applications Pre-treatment for painting: Car, home electric appliances Cleaning: water rinsing after acid treatment of steel plates, water rinsing process in food factory Pipe conn. size:1–2inch, 25–50A Spray angle:40/80° Mean droplet diameter:430–800 μm Strainer:Not included Standard pressure:0.3 MPa (ca. 3 bar) Spray capacity:8.00–39.0 ℓ/min Air Consumption:- Free passage diameter:1.7–5.1 mm

Features Flat spray pneumatic nozzle producing semi-fine (and semi-coarse) atomization having a mean droplet diameter of 50μm or more. (*3) High spray impact with thin flat spray pattern and uniform distribution. Liquid pressure type under the liquid pressures of 0.2–0.5 MPa (ca. 2 bar – 5 bar). Large turn-down ratio with stable spray angle. Spray angle of 60° or 80° *1) Measured at compressed air pressure of 0.4 MPa (ca. 4 bar) and liquid pressure of 0.5 MPa (ca. 5 bar). *2) Free passage diameter of nozzle orifice. *3) Measured by Laser Doppler Method. Applications Cleaning: Printed circuit boards, liquid crystal, liquid crystal display, steel plates [Steel making industry] Surface finish process: Precision cleaning for steel surface treatment, Roll cleaning Thread standard:- Pipe conn. size:Rc 1/8" Standard pressure:- Spray angle:60° or 80° (*1) Spray capacity:0.23–3.0 ℓ/min Supply air type:Compressed air Liquid feeding system:Liquid pressure Mean droplet diameter:20–400 μm (*3) Air Consumption:14–128 ℓ/min, Normal Air pressure:0.2–0.5 MPa (ca. 2 - 5 bar) Free passage diameter:0.8–1.6 mm (*2)

Features Flat spray pattern with uniform distribution throughout pattern area. Small 1/8 pipe connection size for high pressure cleaning. Applications High pressure cleaning: Automotive, containers, tanks, wire and felt parts of paper making machines, wire cylinders, filter presses, other industrial cleaning and degreasing Pipe conn. size:R1/8" Spray angle:15-65° Mean droplet diameter:- Strainer:Not included Standard pressure:0.3 MPa (ca. 3 bar) Spray capacity:2.47–12.4 ℓ/min Air Consumption:- Free passage diameter:0.6–1.7 mm

Features Full cone spray pattern with a round impact area and uniform distribution. Spray capacity ranges from small to medium. X-shaped whirler provides large free passage diameter for minimal clogging. Applications Cleaning: Gas, incinerator fumes, machinery, eliminators, screen, tanks, parts, crushed stones, earth and sand, PCB, others Cooling: Gas, machineries, tanks, steels Spraying: Waste water treatment, aeration, foam breaking, fire extinguishing, dust suppression, sea water desalination, etching, chemical treatment Pipe conn. size:R 1/8" - R 3/8", Rc 3/8" - Rc 3" Spray angle:55-105° Mean droplet diameter:270–1,950 μm Strainer:Available for some nozzle codes Standard pressure:0.2 MPa (ca. 2 bar) Spray capacity:0.50–1,200 ℓ/min Air Consumption:- Free passage diameter:0.4–20.0 mm